Product information "3M FAST-D 8069E Flexible Air Sealing Tape, 75mm x 50m, 0.410mm"
The 3M FAST D 8069E Flexible Air Sealing Tape is an extra strong double-sided adhesive tape for nail-free, wind- and driving rain-proof bonding of rafters and foils, as well as for vapour control layers with plaster in interior and exterior areas. This double-sided tape can be applied to interior and exterior plaster as a nail-free, wind- and driving rain-proof membrane.
Properties
UV-resistant for up to 6 months
The adhesive does not melt or stain in the summer heat
Advantages
Red polyethylene protective film for easy handling and application
Adheres to the most common building and construction substrates (e.g. PE, wood, OSB and concrete) without the use of a primer
As we make up our own adhesive tapes (cut to size), there may be a tolerance of 1-2 mm on the first roll.
0 from 0 Reviews
Give us a rating!
Share your experience with the product with other customers.
Es wurden Maßnahmen ergriffen, um sicherzustellen, dass die veröffentlichten Bewertungen nur von solchen Verbrauchern stammen, die die Waren oder Dienstleistungen tatsächlich genutzt oder erworben haben.
Log in
No reviews found. Go ahead and share your findings with others.
Article no:
41139
SAP number:
41139
Do you need die-cut parts?
We will be happy to provide you with a non-binding offer.
The surface cleaner is used to degrease, clean and prepare parts to be joined before bonding. It can be used on various smooth materials, such as metals, plastic, glass, etc. The surface cleaner consists of isopropanol. Please check compatibility with the materials used before use. Clean all surfaces carefully before each application and only use clean, lint-free cloths. The best bonding results are achieved if you pre-clean the parts to be bonded, then roughen them (e.g. with Scotch-Brite 7447) and clean them again. Make sure that the surfaces are completely dry before you start bonding. For further information, please refer to the safety data sheet, which we will be happy to send you on request to . The product is intended for industrial / professional use only.
For degreasing, cleaning and preparing parts to be joined before bonding. Ideal for use on metals, many plastics and coloured surfaces. The cleaner is a mixture of isopropaneinl and distilled water (70:30). The surface should be checked for compatibility before use.
S-K-S lime-based industrial cleaner removes residues of most dried and non-chemically curing adhesives and sealants, adhesive tapes and films, stickers and labels as well as greasy, oily dirt, tar residues and rubber abrasion. The non-corrosive product gently cleans even stubborn dirt from (un)coated and painted metals, aluminium alloys, stainless steel, glass and ceramics as well as plastics such as ABS, PC, PE, PMMA, PP, PVC, etc. S-K-S is also suitable for degreasing and cleaning equipment and work areas. The surface should be checked for compatibility before use
The hand roller is ideal for pressing on 3M Safety-Walk anti-slip floor coverings and adhesive tapes after installation. Its large roller diameter and weight make it quick and easy to use. Dimensions: 45 mm wide.
Breite in mm:
158 mm
|
Farbe:
Red
|
Körnung:
Very fine
|
Länge in m:
0,224 m
Non-woven fibre hand material for cleaning, deburring, finishing and sanding surfaces in the metal, wood, plastic and other industrial and commercial sectors.
3M Scotch-Weld DP8005 is a viscoplastic 2-component construction adhesive based on acrylate that cures at room temperature. The product is characterised by rapid strength development, high final strength and short processing time, and also impresses with its excellent resistance to water, moisture and media. Scotch-Weld DP 8005 enables the structural bonding of low-energy plastics such as PE, PP and TPE (thermoplastic elastomers) without surface pre-treatment. Plastics such as ABS, rigid PVC, PC, PMMA and fibre composites as well as metals, glass, wood etc. can also be bonded with good strength.
3M Cubitron II Netzblattrollen sind eine schnell schneidende und langlebige Familie von Netzblattrollen, die die außergewöhnliche Schnittleistung und verlängerte Lebensdauer eines Cubitron II Schleifmittels bieten. Sie sind so konzipiert, dass Staubabsauger ihr Bestes geben und praktisch keinen Staub auf der Arbeitsfläche oder in der Umgebung hinterlassen. Kombinieren Sie sie mit einem von 3M empfohlenen Schleif- und Staubabsaugsystem, um das ideale Staubabscheidungssystem für Ihre Werkstatt zu schaffen.
Verbringen Sie weniger Zeit mit dem Schleifen mit 3M Cubitron II Net Sheet Rolls. Unsere schnell schneidenden, langlebigen Netzschleifblätter verfügen über eine Netzunterlage und scharfe 3M Cubitron II Schleifkörner, die zusammen den bestmöglichen Schnitt liefern, ohne die Staubbindung zu beeinträchtigen. Sie sind für die Verwendung mit Standard-Staubabsaugsystemen ausgelegt, einschließlich tragbarer Staubabsauger, zentraler Staubsaugersysteme und Schleifmaschinen mit angebrachten Beuteln. Sie sind in drei Breiten erhältlich - 70 mm (2,75 Zoll), 80 mm (3 Zoll) und 115 mm (4,5 Zoll) - in Stärken von 80+ bis 320+. Sie erledigen Reparaturarbeiten von der Demontage bis zur Lackierung schneller. Ihre lange Lebensdauer bedeutet, dass Sie weniger Schleifmittelwechsel vornehmen müssen, während ihre schnellere Schnittrate bedeutet, dass Sie bei jedem Auftrag weniger Zeit für das Schleifen benötigen. Eine Zeitersparnis, die sich summiert. Die Rollen sind mit Perforationen versehen, die ein bequemes Abreißen von der Rolle ermöglichen. Sie ermöglichen es Ihnen, die Länge des Blattes zu wählen, die Sie für Ihre Arbeit benötigen. Mit 3M Cubitron II Net Sheet Rolls müssen Sie nicht mehr auf Leistung verzichten, um Staub abzusaugen. Sie müssen sich nicht mit Schleifmitteln begnügen, die sich nicht durchsetzen, wie z. B. solche, die langsam anlaufen, aber nicht lange halten, oder solche, die pro Blatt billiger sind, aber trotzdem Ihren Gewinn erhöhen. Kombinieren Sie mit einem von 3M empfohlenen Schleif- und Staubabsaugsystem, um das ideale Staubabscheidungssystem für Ihre Werkstatt zu schaffen.
The 3M Cubitron 3 grinding disc is an extremely fast cutting and durable rigid bonded disc for weld removal and other heavy duty grinding applications. It has a recessed centre that allows grinding at any angle and is suitable for use on almost all materials, with a special formulation for stainless steel, mild steel and aerospace alloys. The 3M Cubitron 3 grinding disc uses the re-engineered 3M Precision Moulded Grain, which utilises proprietary micro-fragments of molecular bond technology. Their structure is created in such a way that they break continuously during the grinding process and always form many sharp cutting edges. These smooth, sharp edges help to create an abrasive that cuts faster, grinds cooler and lasts much longer than conventional abrasives. 3M Cubitron high performance abrasives are designed for professionals who demand more from their equipment. Choose the 3M Cubitron 3 grinding disc to experience the next generation of grinding performance.
When sharpening solid carbide or carbide-tipped tools, only discs with silicon carbide specifications should be used. Due to their special grain shape, you will achieve good results even on very hard workpieces. This disc can also be used for cast iron. A reduction ring set is already included in the packaging and can also be reordered.
Build the right brush for your individual needs. With the radial single segments, you get the proven Scotch-Brite Bristle technology of the Cubitron ceramic abrasive grain encapsulated in solid plastic and achieve consistent work results over the entire service life. With their curved bristles (type C), the RB-ZB single segments belong to the most flexible Scotch-Brite Bristle variant. They are ideal for cleaning and light deburring applications in hard-to-reach work areas, especially as they are also available in smaller diameters. With the MN-AC mandrel, the individual segments are combined (1 segment=approx. 1.6 mm wide).
These carbide end mills have been specially developed for use on stainless steel and manufactured on state-of-the-art CNC grinding machines. The newly developed geometry enables cool grinding with maximum tool life on hand-held, pneumatic and electric machines. The aggressive cutter shape is particularly long-chipping and thus ensures a large stock removal rate. Reduced heat generation protects the milling cutter and the workpiece.
€31.02*
Data protection notice
The video will be loaded after your confirmation via the video portal YouTube. By confirming, you agree to load the videos on this page from the external provider YouTube in compliance with the GDPR.