3M Roloc grinding wheel 361F, 50.8 mm, P36 #22398

Quick-change disc with excellent price-performance ratio. Colour coding makes it easy to differentiate between grit sizes. Equipped with aluminium oxide grit and cloth backing for general sanding and removal work.

Quick-change disc with excellent price-performance ratio. Colour coding makes it easy to differentiate between grit sizes. Equipped with aluminium oxide grit and cloth backing for general sanding and removal work.

Rubber backing pad with metal threaded core and integrated ¼" holder for direct use on 3M Roloc angle grinders. Especially suitable for use with Roloc Bristle, non-woven, abrasive and fibre discs. The dimensions must be selected according to the diameter of the grinding tool.

Quick-change disc with excellent price-performance ratio. Colour coding makes it easy to differentiate between grit sizes. Equipped with aluminium oxide grit and cloth backing for general sanding and removal work.

Can be screwed into ¼" receptacle. Backing pad 05539 and 05540 additionally with fixing screw and nut for 7/16'' - 20 UNF thread (USA).

Scotch-Brite CR-DR is suitable for all applications on metals and paints, in particular for removing rust, corrosion, old coatings, sealant residues and tarnish, for derusting and removing paint from sheet metal parts and for cleaning metal surfaces and weld seams.

For highly efficient liquid filtration from the outside to the inside, use the 3M filter cartridges Series 740.  In applications with high requirements for contaminant separation, our filter cartridges allow higher flow rates than standard products with a diameter of 6.35 cm. This means that significantly fewer filter cartridges are required for a given flow rate.  The filter medium used in the 3M 740 series filter cartridges is based on 3M polypropylene microfibre. Our manufacturing processes enable production according to strictly controlled specifications. The result is a filter media with consistent and predictable particle retention properties. The microfibre media is radially pleated (a 3M innovation) - this optimises the usable filter area of the inserts. End caps, outer sleeves and cores made of polypropylene from the 3M filter cartridge series 740 protect the pleat composite and result in a robust filter construction. A double O-ring seal reduces the risk of liquid bypassing the filter. 3M filter cartridges series 740 are available for particle sizes from 1 μm to 70 μm (with a particle separation efficiency of 99.9 %). The 3M filter cartridges series 740 are pleated polypropylene microfibre depth filters. They are suitable for filter housings that accommodate large filters with an outer diameter of 16.51 cm, a length of 101.6 cm and a 226 O-ring connection.

For the highest demands on surface quality, combined with high cutting performance and an exceptional finish.

Adhesive tape for covering during chrome plating as protection against budding and as radiation protection and for labelling in X-ray technology.

This ceramic-bonded internal cylindrical grinding tool offers you a cost-effective alternative to CBN tools with a good stock removal rate. The AT60 sintered aluminium oxide compound can be used universally. You can choose the right tool for you from our wide range.

3M UHMW (ultra-high-molecular-weight) polyethylene sliding tapes have a highly slippery surface due to their low coefficient of friction. They also have excellent abrasion resistance. The optimum combination of these properties makes these adhesive tapes particularly suitable for use as sliding tapes. These tapes are also self-lubricating, resistant to moisture and many chemical agents. They are repellent to most dry or pasty substances and have good puncture and impact resistance. The 3M sliding tapes differ in terms of thickness and different adhesive versions.

Deburring of shaft and piston rods before hard chrome plating; deburring of turbine blades, stamped flat parts, thread guides and machine parts, gear wheels, die-cast and injection-moulded parts, automotive parts (e.g. piston rings, pistons), parting lines on cast and pressed parts; Attention: The direction of rotation must be observed!