Ready for immediate dispatch, delivery time approx. 1 - 3 working days
This fast curing epoxy tin replacement filler is suitable for repairing surface damage (such as dents) on metal parts, reshaping surfaces and completely sealing welds (to protect them from corrosion). The 3M Epoxy Tin Replacement Filler has a unique formulation, is lead-free and contains 100% solids so it does not shrink during curing. It has excellent adhesion and anti-corrosion properties. With a working time of approx. 15 to 20 minutes and a curing time of approx. 4 hours at 22 °C, 3M Epoxy Tin Filler enables fast processes in the bodyshop. Curing can be further accelerated by IR drying. The classic open flame tinning process still used today is easily replaced by the use of 3M Epoxy Tin Filler. This makes it possible to avoid high temperatures in the process, which is particularly relevant for certain modern vehicle materials such as high-strength thin steels, composites, etc. There is no need to handle open flames or remove heat-sensitive vehicle parts, as room temperature is sufficient for processing and curing the products. After curing, the material can be sanded without any problems and then painted as normal. Follow the paint manufacturer's instructions.
- Excellent corrosion protection
- No shrinkage - 100 % solids
- Fast curing
- For steel, zinc and aluminium surfaces
- Lead-free alternative to the classic tinning process
- Very good sandability
- Can be sanded after 20 minutes with forced drying; air drying: four hours (at 22 °C)
- The material can be reworked with itself
- Ideal for modelling/shaping hard-to-reach areas
H332 Harmful if inhaled.
H314 Causes severe skin burns and eye damage.
H317 May cause an allergic skin reaction.
H336 May cause drowsiness or dizziness.
P260A Do not breathe vapour.
P280D Wear protective gloves, protective clothing and eye/face protection.
P303 + P361 + P353A IF ON SKIN (or hair): Take off immediately all contaminated clothing. Rinse skin with water/shower.
P305+ P351 + P338 IF IN EYES: Rinse cautiously with water for several minutes. Remove any contact lenses if possible. Continue rinsing.
P310 Immediately call a POISON CENTER or doctor.
P333+ P313 If skin irritation or rash occurs: Get medical advice/attention.
Log in
Montag, 25. März 2024
Friedhelm L.
Danke
jederzeit wieder
Samstag, 13. Januar 2024
Hans-Gunther R.
Sehr gutes Produkt zum Top Preis
Sehr gutes Produkt zum Top Preis
Montag, 8. Januar 2024
Uwe E.
Sehr gutes Produkt und sehr gute Abwicklung
Sehr gutes Produkt und sehr gute Abwicklung von der Bestellung bis zur Lieferung, vielen Dank
Samstag, 2. Dezember 2023
Lara Andrea W.
Top
Top
Samstag, 18. November 2023
Helmut B.
Super Produkt
Sehr gut zu verarbeiten. Gute Formbarkeit.
Dienstag, 26. September 2023
Klaus B.
super qualität.
top qualität. gut zu verarbeiten. es wäre besser wenn man die anzahl der mischdüsen bei der bestellung wählen könnte.
Sonntag, 10. September 2023
Julian H.
Das Produkt hält was es verspricht. Wirklich
Das Produkt hält was es verspricht. Wirklich eine super alternative zum herkömmlichen Verzinnen. Wenn keine pneumatische Kartuschenpresse vorhanden ist, wird das Auftragen zu einem Kraftakt. Einzelne Mischdüsen zum Nachkaufen hatte ich bis jetzt keine gefunden. Man will das teure Material ja nicht wegschmeißen. Würde das Produkt trotzdem wieder verwenden!
Montag, 31. Juli 2023
Norbert M.
,ø¤º°`°º¤ø,¸¸,ø¤º° TOP EBAYER º°`°º¤ø,¸¸,ø¤º°º°`°º¤ø,¸¸,ø
,ø¤º°`°º¤ø,¸¸,ø¤º° TOP EBAYER º°`°º¤ø,¸¸,ø¤º°º°`°º¤ø,¸¸,ø
Donnerstag, 13. Juli 2023
Knut H.
3M funktioniert immer
3M funktioniert immer